Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

Entries Tagged as 'Dodge'

2003-Up Dodge Ram 2500/3500 Custom Quick Install Mounting Kit

December 11th, 2010 · No Comments

Installation Instructions CUSTOM QUICK INSTALL MOUNTING KIT Dodge Ram 2500/3500 Standard & Quad Cab, 2003 & Up Dodge Ram Megacab 1500/2500/3500, 2006-2008 Part Numbers: 50062
1. Lower and remove spare tire.
2. Detach the wire harness from the inside of the driver side frame between the fuel tank and the shock absorber mount.
3. Place the rear mounting [...]

[Read more →]


1997-2005 Dodge Brakesmart Installation Instructions

December 11th, 2010 · No Comments

1. Release the hood latch and lift the hood of the vehicle.
2. Locate the brake lines connected to the brake master cylinder.
3. There is a service tee included in the hookup kit. The Dodge installation seems to be easier if the forward brake line is used for the service tee.
4. Remove the brake line from [...]

[Read more →]


Dodge Magnum Bass Slammer DMAGW02*10U Install Sheet

December 11th, 2010 · No Comments

MOUNTING LOCATION: The enclosure mounts in the rear drivers’ side panel behind the back seat, side-fire, in Dodge Magnum Wagons.
INSTALLATION: Follow the steps below
1. Attach the included mounting bracket and adhesive foam pads to your enclosure as shown below.
2. Place gasket provided around woofer hole cutout. Connect black wire to the negative side of woofer [...]

[Read more →]


2006 Dodge Dakota/Mitsubishi Raider Air Charger P/N. 63-1546

December 11th, 2010 · No Comments

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Loosen the hose clamp at the throttle body and the air box mounting nut and then disconnect the crank case vent hose from the inline fitting.
3. Disconnect the stock intake tube from the intake plenum and lift to remove the air box [...]

[Read more →]


Dodge Ram Truck 2500/ 3500 5.9L Turbo Diesel ETB, ETC Engine Idendification

December 10th, 2010 · No Comments

General precautions
Disconnect battery ground cable.
Do NOT turn crankshaft or camshaft with timing gear(s) removed.
Remove glow plugs to ease turning engine.
Turn crankshaft in normal direction of rotation (unless otherwise stated).
If fitted: Mark position of crankshaft position (CKP) sensor before removal.
Do NOT turn crankshaft via camshaft or other gears.
Observe all tightening torques.
Check diesel injection pump timing after [...]

[Read more →]


Dodge #727-DD Mag-Hytec Transmission Pan

December 10th, 2010 · No Comments

The Mag-Hytec pan is designed to fit the factory Dodge #727 transmission body as supplied as original equipment. However, in some applications, or because of the use of certain factory options and/or after market equipment, there may be clearance problems between your Mag-Hytec pan and other vehicle components. It is the responsibility of the vehicle [...]

[Read more →]


2003-2007 Dodge Trucks Direct Mount Exhaust Brake Installation

December 10th, 2010 · No Comments

Thank you and congratulations on your purchase of a Pacbrake Direct Mount exhaust retarder. Do not install the kits listed below on 2003 model year Dodge trucks built up to June 27th, 2005 with automatic transmissions without a transmission controller.
Pacbrake kit information and applications covered in this manual:

[Read more →]


02-08 Dodge Ram 1500 Quad Cab DU-HA Dark Gray P/N #30017

December 10th, 2010 · No Comments

Installation Instructions:
1. Flip the rear seat bottom up. If your truck came equipped with the optional metal trays, remove each tray by removing the two large bolts using a 18mm socket and the two small nuts using a 13mm socket. Once you have removed the metal trays, replace the braces, large bolts and smaller nuts.

[Read more →]


Dodge Sprinter 2007-2008 XSVI-1784-NAV Installation Instructions

December 10th, 2010 · No Comments

In the Dodge vehicle listed above there are no 12 volt accessory wires currently in the factory harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio. The XSVI-1784-NAV is designed to provide a 12 volt 10 amp switched accessory output along with [...]

[Read more →]


2003-2010 Dodge Ram 2500/3500 8″ Long Arm Suspension Install Instructions

December 9th, 2010 · No Comments

STEP Installations of Long Arm Suspension on Dodge Ram 2500/3500
1. Working on the driver side, remove the stock sway bar from the stock sway bar end link. Repeat the procedure on the passenger side. Now remove the stock sway from the stock end links and let the stock sway bar hang. Special note: Step # [...]

[Read more →]




?>