Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

1995 Isuzu Trooper LS Timing Belt Remove & Installation

May 23rd, 2010 · No Comments

This document covers the steps of Timing Belt installation for 1995 Isuzu Trooper LS
Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil [...]

[Read more →]

Tags: Isuzu

2004 Hyundai Santa Fe Timing & Counterbalance Shaft Belts Installation

May 22nd, 2010 · No Comments

This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur.
Removal
CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate direction of rotation before removing.
1. Remove drive belts [...]

[Read more →]

Tags: Hyundai

2004 Mitsubishi Lancer O-Z Rally Timing Belt Installation

May 22nd, 2010 · No Comments

REMOVAL SERVICE POINT TIMING BELT REMOVAL
CAUTION: The crankshaft should always be turned only clockwise. 1. Turn the crankshaft clockwise (right turn) to align each timing mark and to set the number 1 cylinder at compression top dead center. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry [...]

[Read more →]

Tags: Mitsubishi

2003 Hyundai Elantra GLS Timing Belt Removal and Installation

June 5th, 2010 · No Comments

This pdf covers the timing belt guide for HYUNDAI 1.8L & 2.0L 4-Cylinder – 1996-04 (Except Sonata & 2004 Elantra).
Removal 1. Remove all drive belts and drive pulleys from crankshaft and water pump. Remove generator bolt, if necessary. Remove crankshaft pulley and water pump pulley. 2. Remove timing belt covers and gaskets, noting bolt lengths [...]

[Read more →]

Tags: Hyundai

1998 Nissan Altima SE Timing Chain Installation

February 28th, 2011 · No Comments

1. Remove spark plug wires. Set No. 1 piston at TDC on its compression stroke. Remove vacuum hoses, electrical harness, connectors, and harness clamps. Remove power steering pump, A/C compressor, and alternator belts. Remove power steering reservoir tank and reposition it for clearance. Install engine support eye bracket at right rear of cylinder head, then [...]

[Read more →]

Tags: Nissan

2002 Kia Truck Sedona EX V6-3.5L Timing Belt Service & Repair

May 16th, 2010 · No Comments

Removal
1. Remove the engine cover.
2. Remove the drive belt.
3. Remove the idler pulley, crankshaft pulley, power steering pulley and tensioner pulley.
4. Remove the upper and lower timing belt cover.
5. Support the engine with garage jack or special tool, and then remove the engine
mounting insulator. Caution: Take care not to deform the engine oil pan.

[Read more →]

Tags: Kia

1997 Honda Passport LX Timing Belt Installation

May 20th, 2010 · No Comments

This manual covers the removal and installation of timing belt for honda passport lx. Removal
1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts.
2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler [...]

[Read more →]

Tags: Honda

1996 Toyota Avalon XL Timing Belt & Components Removal

May 22nd, 2010 · No Comments

Removal (1994-97 3.0L V6) 1. Disconnect negative battery cable. Remove coolant reservoir. Raise and support vehicle. Remove right side front wheel. Remove right lower engine cover. Remove accessory drive belts. 2. Remove engine stabilizer rod, engine mounting bracket and right engine mount brace, located near timing belt cover. Remove the alternator bracket for access to [...]

[Read more →]

Tags: Toyota

1988 Mazda Truck B Series Truck Timing Belt

November 23rd, 2010 · No Comments

1988 Mazda Truck B Series Truck L4-2184cc 2.2L 2200. Vehicle Level Engine, Cooling and Exhaust and Installation – Engine – Timing Belt – Service and Repair – Timing Belt Removal.
1. Align the timing mark on the timing belt pulley and camshaft pulley with the marks.
2. Remove all the spark plugs. NOTE: This is to prevent [...]

[Read more →]

Tags: Mazda

1989-97 Nissan 300ZX Timing Belt Removal and Installation

February 27th, 2011 · No Comments

REMOVAL INTERFERENCE ENGINE. In the event of timing chain failure, it is probable that valve to piston damage has occurred. A compression test should be carried out on all cylinders before removing the cylinder head.
1. Remove engine under cover.
2. Drain engine coolant from cylinder block.
3. Remove: radiator, – all drive belts, – cooling fan and [...]

[Read more →]

Tags: Nissan


?>