Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

2004-2008 Mazda 3 Kit PART 99-7504 Installation Instructions

October 25th, 2009 · No Comments

KIT FEATURES
• DIN Mount Radio Provision with Pocket
• ISO Mount Radio Provision with Pocket
• Bonus Display Replacement Pocket
• Retains Factory Display For Automatic
Climate Controls
A) Radio Housing • B) ISO Brackets • C) Trim Plate • D) Display Replacement Pocket • E) Display Retention Brackets • F) (2) 3/8” #10 Bolts and (2) #10 Nuts.
(more…)

Continue Reading Entry... »

→ No Comments

1995-2001 Mazda Millenia Pro.Vit VSM Installation Instructions

October 25th, 2009 · No Comments

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
TOOLS REQUIRED: Small flat screw driver, #2 Phillips screwdriver, hook tool, 5/64” drill bit, and drill, marking pen
STEP 1.
Begin by opening center console storage compartment door. Remove inner storage compartment box by releasing clips located on each side. To do this, insert small flat screw driver in between box and padded molding on center console unit. Release one side at a time. Lift unit out and set aside.
(more…)

Continue Reading Entry... »

→ No Comments

2003-06 Mazda 6 L4-2.3L K&N Dry-Charger Instructions

October 25th, 2009 · No Comments

The K&N Dry-Charger included with this kit must be installed on the K&N Air Filter when used with this K&N Typhoon Cold Air Intake System. The K&N Typhoon Intake System is a performance product that can be used safely during mild weather conditions. During harsh and inclement weather conditions, you must convert your Cold Air Intake System to a short ram configuration, or return your vehicle to the stock OEM air box and intake tract configuration. Failure to follow these instructions can void your warranty.
(more…)

Continue Reading Entry... »

→ No Comments

2001 Mazda 626 Specific Vehicle Alarm Fitting Instructions

October 25th, 2009 · No Comments

ALARM/SIREN POSITION
Position the compact alarms and the sirens in the engine compartment, on the bulkhead of the support of the passenger’s side shock absorber. Pass the cables through the rubber sleeve above the lung of the servobrake.
POWER SUPPLY
+ 30: connect to the 4 mm2 WHITE/RED wire located in the multiway connector placed behind the fuse box.
- 31: connect to the car body.
IGNITION WIRE
+ 15/54: connect to the 2,5 mm2 BLUE wire with SILVER references located in the wiring harness coming out of the 8 way connector, in the lower part, behind the fuse box.
(more…)

Continue Reading Entry... »

→ No Comments

08 Mazda 3 Automatic Cruise Control Installation Instructions

October 24th, 2009 · No Comments

INSTALLATION PREPARATION:
1. DISCONNECT NEGATIVE BATTERY CABLE BEFORE INSTALLATION.
2. REMOVE THE STEERING COLUMN SHROUD AND LOWER DASH PANEL.

HARNESS INSTALLATION:
1. LOCATE THE WHITE CONNECTOR AT THE IGNITION SWITCH. CONNECT THE RED IGNITION WIRE (+12V IGNITION) FROM THE MAIN CRUISE HARNESS TO THE GREEN/RED WIRE OF THE IGNITION SWITCH CONNECTOR.
2. LOCATE THE YELLOW 12-PIN CLOCK SPRING CONNECTOR AT THE LEFT SIDE OF THE STEERING COLUMN.
(more…)

Continue Reading Entry... »

→ No Comments

2003-2005 Mazda 6 Dash Disassembly Installation Instructions

October 24th, 2009 · No Comments

Electronic Climate Control
1. Disconnect the negative battery terminal to prevent an accidental short circuit.
2. Unscrew the shift knob counter clockwise to remove. (Figure A)
3. Unclip and remove the cup holder/parking brake cover and shifter cover as one unit. (Figure B)
4. Remove (2) Phillips screws from the bottom of the radio/climate control panel. (Figure C)
5. Open glove box, squeeze sides together and let open fully then remove (1) 10 MM bolt from the side of the radio bracket.
(more…)

Continue Reading Entry... »

→ No Comments

03-05 Mazda 6 Lower Grilles Install Instructions

October 24th, 2009 · No Comments

This is what your Mazda 6 looks like before the GrilleGuy grille. That is about to change. Please allow approximately 30 minutes for the complete grille installation. You will need to remove the upper grille to simplify the install by allowing you to access the back of the lower grille. You could opt to remove the under-pinning and come from the bottom of the vehicle, if needed. The upper grille is removed by removing the fasteners from the top and then releasing the gibs where the grille meets the front bumper cover.
(more…)

Continue Reading Entry... »

→ No Comments

1992-2001 Ford Escort/ZX2 Short Throw Shifter Installation Instructions

October 24th, 2009 · No Comments

This B&M Short Throw Shifterhas been designed to work on most 1992 – 2001 Ford Escort/ZX2, 1992-1999 Mazda MX-3/30X, 1992-1994 Mazda 323, and 1992-2002 Mazda Protegé/MP3/5 models. It has been engineered to greatly reduce shift throw and improve shifter feel. Check the parts and tools lists at the beginning of these instructions for the supplied parts and the tools required to install your B&M Short Throw Shifter. Installation of the B&M Short Throw Shifter can be accomplished by anyone with minimal mechanical experience.
(more…)

Continue Reading Entry... »

→ No Comments

1998-00 Ford Ranger & Mazda Pickup Body Lift Kit Installation Instructions

October 24th, 2009 · No Comments

Installation of a body lift will change the center of gravity and the handling characteristics of the vehicle. Because of the higher center of gravity and larger tires, the vehicle will handle and react differently both on and off-road. You must drive it safely! Extreme care must be taken to prevent vehicle rollover or loss of control, which could result in serious injury or death. Avoid sudden sharp turns or abrupt maneuvers and always make sure all vehicle occupants have their seat belts fastened.
(more…)

Continue Reading Entry... »

→ No Comments

Mazda Miata MX-5 Boot Lid Lifter Fitting Instructions

October 23rd, 2009 · No Comments

1. Examine the lift arm. The “thick” end (with the sticker) is terminated with a threaded bolt. This can be detached by removing (with a flat screwdriver blade) the thin metal band. However, this should not be necessary. Do not attempt to compress the lift with your bare hands – it won’t move unless you are very strong. It’s useful to remove the silver-coloured nut and lock washer from the head of the lift before starting.
2. Remove the trunk mat. Unscrew and remove the box in the well on the left of the trunk.
3. Remove the four plastic pop-fasteners which retain the cover of the left-hand side of the trunk lining. (To remove a fastener, insert a fine blade between the middle of the head and the outer ring, and wiggle the head.) Now carefully remove the trunk lining panel.
(more…)

Continue Reading Entry... »

→ No Comments

?>