Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

1939 Chevrolet Taillights Installation Instructions

December 31st, 2010 · No Comments

Installation Instructions
1. Disconnect Battery. Do not skip this step. Also, do not try to “test” the LED array by connecting the leads directly to your battery. Permanent damage will occur to the LED array if you fail to heed these steps.
2. Remove Taillight housings from car.
3. Remove bezel and lens.
4. Remove light bulb and bucket. [...]

[Read more →]


2009-up Dodge Challenger Hurst Billet Comp/Plus Shifter

December 8th, 2010 · No Comments

This shifter is constructed of a solid billet steel and chrome plated upper stick, billet aluminum transmission carrier, and billet stainless steel adapter, lower stick, pin, and Energy Suspension® polyurethane bushing housing. You can expect reduced shift throw (over 30%), increased strength and better, firmer, yet smoother and more precise feel thanks to extremely tight [...]

[Read more →]


2005-2006 Subaru Part Number: SUB-100-05 Installation Instructions

November 22nd, 2010 · No Comments

READ INSTRUCTIONS COMPLETELY BEFORE INSTALLING THIS BRACKETRON PHONE MOUNT. All instructions are written from the drivers seat position looking forward at the vehicle dash. We advise caution whenever your removing or handling plastic parts of a vehicles dash. WARNING: Unnecessary force or pressure can cause pieces to crack or break. Logo and part number will [...]

[Read more →]


1996-97 Subaru Impreza Outback Part Number: SU-50-96 Installation

November 20th, 2010 · No Comments

All instructions assume a drivers seat vantage point. Caution is advised when removing and reassembling wood or plastic parts of a dash. Applying unnecessary force or pressure may cause a piece to crack or break.
Pro.Fit logo and part number will be right side up and readable when installed.
TOOLS REQUIRED: #1 Phillips screwdriver, hook tool, marking [...]

[Read more →]


Jazzy Engineering Aux-in Accessory for 2002-04 Subaru WRX Installation Instructions

November 17th, 2010 · No Comments

REMOVE THE CDS
For the initial installation steps, it is not necessary to have the accessory board available. Set it aside in a safe place and then proceed to your vehicle with the recommended installation tools. Before you begin taking apart your car, remove all the CDs from the radio so that they won’t move inside [...]

[Read more →]


Video Out From a Dodge/Chrysler DVD Head Unit Tech Tips

November 11th, 2010 · No Comments

Micah Williams of Audio Specialists, Inc. in Hopkinsville, Ky., shows how to create a video output from the factory radio in a Dodge Nitro that can be used on rear screens. Williams says that this technique will work on any Dodge/Chrysler radio that includes the factory six-disc DVD changer. He notes that the easiest way [...]

[Read more →]


Mitsubishi Eclipse Gauze Bezel Model 20012 Installation Instructions

September 18th, 2010 · No Comments

Removal of Factory bezel:
1. Remove both screws from top of factory bezel.
2. Pull straight out on the bottom of the bezel to release clips. Pull on one side of the bezel at a time (to the left and right side of the steering wheel).

[Read more →]


Toyota Kit Components 99-8100 Installation Instructions

August 29th, 2010 · No Comments

2-SHAFT HEAD UNITS: Snap the Faceplate onto the front of the Radio Housing. (For applications using Faceplate #2, cut and remove the bottom portion of the Faceplate). Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A)
DIN HEAD UNITS: Cut and remove the shaft supports from the Faceplate and [...]

[Read more →]


Ford F150 Aftermarket DVD Installation Instructions

April 6th, 2010 · No Comments

Cutting template for DVD harness
Attach one large bin and one small bin (included with DVD kit)
Using template provided, cut a rectangular hole in headliner as shown on template.
Remove large and small bins from headliner.
Removing Trim
Remove caps and unscrew bolts on “A” pillar trim.
Remove “A” pillars.
Pull cover open on seat belt Shoulder bracket to expose bolt.
Remove [...]

[Read more →]


1999-2003 Ford Windstar Pro.Fit VSM Instructions

April 5th, 2010 · No Comments

Installation prodecure:
STEP 1.
Begin by inserting the radio removal tools into the holes on the face of the radio. Apply outward pressure on the tools while simultaneously sliding the radio out of its cavity. Disconnect all wiring to the radio and remove the radio removal tools. Set the radio aside. Using the 9/32″ socket and driver [...]

[Read more →]




?>