Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

How much would it cost to replace breaks on a ‘06 Nissan Sentra?

December 21st, 2010 · No Comments

I need to get them done ASAP and would like to know where I should go and how much it would be.
Ans: Since you have a newer car, go to your Nissan dealer. Whenever I have newer vehicles I try to take them to my dealer for all maintenance simply because I think it looks [...]

[Read more →]


How hard is it to remove the rotors on a nissan pathfinder?

December 20th, 2010 · No Comments

I need to get the rotors turned and it is so much cheaper to take them off yourself and have them turned somewhere.
It will take near 20 minuets to remove the brake rotor. Do one side at a time, block the rear wheels if its the front you will remove. Use safety stands, remove the [...]

[Read more →]


1995 Mazda MX-6 Brake System Remove & Installation

December 1st, 2010 · No Comments

FRONT DISC BRAKE PADS
Removal & Installation
1. Raise and support front of vehicle. Remove front wheel assemblies. Remove lower lock pin/guide bolt. See Fig. 2 . Pivot caliper upward and support using rope.
2. Remove pads, shims, guide plates or pad guides and “V” springs (if equipped). Replace pad if lining thickness is less than specified. See [...]

[Read more →]


1998-2005 Audi C5 Wheel Bearing Unit, Removing and Installing

November 7th, 2010 · No Comments

Removing
Remove decorative wheel cover, for light-alloy wheels pull off protective cap (use pulling hook in vehicle tool kit). Remove bolt for driveshaft. (Only remove when vehicle is standing on its wheels: danger of accident). Remove wheel. Secure brake rotor using a wheel bolt. Remove bolt. Pull cable of ABS wheel speed sensor out of bracket [...]

[Read more →]


Installation and Removal of Wheel Bearings: How to proceed?

November 3rd, 2010 · No Comments

We go installation of topic dedicated on with our to the wheel bearings. In this issue we will look at non-driving rear wheels, and consider two types of bearings:
- Cartridge double-row tapered-roller bearings,
- Hub double-row ball bearings.
Cartridge bearings with two rows of tapered rollers are used for the non-driving rear wheels of compact and mid-size [...]

[Read more →]


2003 Dodge Pickup R1500 Axle Shafts Front Installation

May 22nd, 2010 · No Comments

Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential to front wheels. Both axle shafts are identical and interchangeable, 3-piece units consisting of outer Rzeppa joint, solid interconnecting shaft and inner tripod joint. Both Rzeppa joints and tripod joints are true Constant Velocity [...]

[Read more →]


1991 Infiniti G20 Axle Shafts – Front Removal & Installation

May 20th, 2010 · No Comments

Axle shafts transfer power from transaxle to drive wheels. Axle shafts consist of a shaft and flexible Constant
Velocity (CV) joint at each end. See Fig. 1 . Inner CV joint is splined to transaxle. Outer CV joint is splined to
hub assembly and secured by wheel bearing lock nut.
Inner CV joint is a plunging tripod joint. [...]

[Read more →]


97-03 Ford F150 2wd 3″ Spindle Lift Installation Instructions

March 21st, 2010 · No Comments

INSTALLATION STEPS
1. Jack up the front of the truck and support the frame rails with jack stands. The tool list is on the back page. NEVER WORK UNDER AN UNSUPPORTED VEHICLE.
2. Starting on the passenger side of the truck remove the front tire. Remove the brake calipers from the spindle bracket using a 13 mm [...]

[Read more →]




?>