Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

Flip-Over Hitch Model 218 Chevrolet/GMC 2001-2007 1-Ton Installation

January 28th, 2011 · No Comments

Most pick up trucks have FUEL LINES and/or BRAKE LINES and/or ELECTRICAL WIRING positioned along the truck framerails where your Flip-Over hitch will install. BEFORE INSTALLATION identify and examine the location of fuel lines, brake lines and electrical wires. Be sure you will not damage fuel lines, brake lines or electrical wiring when positioning the [...]

[Read more →]


Camshaft Timing Offset Bushing Kit Installation Instructions

January 15th, 2011 · No Comments

Fits all Chevrolet V8’s 262 thru 400, 348-409, and 396-402-427-454 Cu.In. Also, Chrysler “B” wedge engines and 426 Hemi engines.
Installation Instructions
Camshaft timing gear must be removed from engine. Place gear with bolt head side down on drill table. Drill all four holes (3

[Read more →]


Bed X-Tender Assemblies Installation Instructions

November 25th, 2010 · No Comments

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list. Read and understand instructions completely before beginning installation.
STEP 2. Position and hold template on passenger side for square bracket as shown. (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to ‘94, and MAZDA up to ‘94 [...]

[Read more →]


2001 CR-V Trailer Hitch Installation

November 14th, 2010 · No Comments

Advise the customer to read the owner’s manual carefully before using the trailer hitch. It has important safety and operation information. Installation procedure the trailer hitch on 2001 Honda CR-V:
1. If equipped, write down the customer’s radio station presets; the radio memory will be erased when you disconnect the battery.
2. Disconnect the negative cable from [...]

[Read more →]


2010 Honda CR-V Tailgate Spoiler Installation Instructions

November 13th, 2010 · No Comments

Tailgate Spoiter installation on Honda CR-V 2010:
NOTE: Be careful not to damage the tailgate and the body paint finish.
1. Open the tailgate. Insert a flat-tip screwdriver into the specified position of the right tailgate trim, and remove the pin as shown.
2. Remove the clip and the right tailgate trim.
3. Remove the left tailgate trim in [...]

[Read more →]


Mazda MX6/LS QuickLIFT Installation Guide

April 21st, 2010 · No Comments

Step 1 – Unpack QuickLIFT kit and verify contents.
Remove all items from the packing tube. You should have the following before beginning:
* (2) Gas springs (RT-QL-200-A5A)
- Be sure to cycle each gas spring a few times before installing.
* (4) 3/16″ Multi-grip Rivets
* (4) Steel brackets – 2 fender, 2 hood.
* Printed Color Instructions
* Gas Spring [...]

[Read more →]


2001 Ford Escape Air Spring Installation Instructions

March 18th, 2010 · No Comments

I. Installing the Air Cylinder
1. Jack up rear of vehicle or raise on hoist. Support frame with safety stands. Lower axle or raise body of vehicle until suspension is fully extended.
2. Pry the stock jounce bumper out of the jounce bumper bracket and discard (Figure 1).
3. Remove the upper jounce bumper retainer bracket by removing [...]

[Read more →]


1998-2004 Ford Ranger QuickLIFT Installation Guide

March 10th, 2010 · No Comments

Step 1 – Unpack QuickLIFT kit and verify contents.
Remove all items from the packing tube. You should have the following before beginning:
* (2) Gas Springs – Be sure to cycle them a few times before installing!
* (4) 3/16″ gold shafted rivets – for hood brackets
* (2) 3/16″ Multi-grip rivets – center hole of hood brackets
* [...]

[Read more →]


2006-2007 Ford F-53 Chassis Motorcoach Front Installation Instructions

March 3rd, 2010 · No Comments

Installation
1. Place the coach on a level concrete surface. Measure each side of the coach from the front wheel well to the ground. Record these measurements as you will need them in Step 9.
2. Place a jack under each side of the frame just behind the leaf spring shackles. Jack the coach up high enough [...]

[Read more →]


1994-2002 Dodge Ram 2500/3500 5.9L Cummins Smokers S8100409 Installation Instructions

December 18th, 2009 · No Comments

Removal of Stock System:
1. Separate the stock exhaust system at the slip joint by the muffler. Remove the rear exhaust from rubber hangers and remove the system from under the truck.
2. Using a 15mm socket or wrench, remove the two (2) bolts at the turbo flange and remove the stock down pipe.
Installing Your Front Section [...]

[Read more →]




?>