Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

What kind of 5 speed manual transmission comes in a 1995 chevrolet c/k 2500 4×4?

January 2nd, 2011 · No Comments

I have a 1995 chevy 4×4 3/4 ton with a 5 speed manual i cant seem to figure out how to determine what kind of transmission i have.

[Read more →]


How much will it cost to replace the engine in a 1998 Chevrolet Cavalier?

December 31st, 2010 · No Comments

I think that I can get the motor myself at cherry auto parts for around 700.00.I was just wondering if I do it that way how much it will cost to have someone put it in for me.Also, the air doesn’t work, so any ideas on how much that will cost and what might be [...]

[Read more →]


Where is the voltage regulator in a 92 Cadillac Eldorado?

December 25th, 2010 · No Comments

- It is built into the alternator,you’ll need to replace the alternator,I would purchase an AC Delco re-manufactured alternator at my local auto supply store.I have found through experience that the chain stores such as Auto-Zone carry cheaply made parts.I and others with our experience find it best to buy our parts from an independent [...]

[Read more →]


How do you siphen gas out of an 88 Cadillac?

December 25th, 2010 · No Comments

Car broke down with a full tank of gas. Going to sell the car, but, would like to put most of the gas in another car. Doesn’t it have a screen on it that prevents you from siphening gas out? Let me add, this is not my car. It’s my friends car. He said I [...]

[Read more →]


2006 ARB Dodge Sahara Bar Media

December 16th, 2010 · No Comments

Seattle, May 8/ ARB 4×4 Accessories/ — Australian based four-wheel parts manufacturer, is proud to announce the expansion of their full size winch ready bumpers by releasing the new ARB 2006-2009 Dodge Sahara Bar.
Considering ARB’s twenty-year history manufacturing both original equipment and aftermarket accessories for vehicles around the world, you can be sure to expect [...]

[Read more →]


1998-01 Dodge RAM 1500 Quad Cab Step Bar Assemblies

December 14th, 2010 · No Comments

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against parts list. Read and understand instructions completely before beginning installation.
STEP 2. Install bolt plates into inner support panels near rear body mounts for both passenger and driver side as shown. Use plastic bolt retainer to ensure bolt plate [...]

[Read more →]


06-Up Dodge 4WD 1500 2.5″ Suspension Kit

December 13th, 2010 · No Comments

Installation Instructions for 2.5″ Suspension Kit on Dodge 4WD:
1. Jack up the front of the vehicle and support the vehicle with jack stands, so that the front wheels are off the ground.
2. Using 22mm socket remove the front tires/wheels.
3. Using 21mm socket remove the nut from the steering linkage. Using a hammer hit on the [...]

[Read more →]


1997-2005 Dodge Brakesmart Installation Instructions

December 11th, 2010 · No Comments

1. Release the hood latch and lift the hood of the vehicle.
2. Locate the brake lines connected to the brake master cylinder.
3. There is a service tee included in the hookup kit. The Dodge installation seems to be easier if the forward brake line is used for the service tee.
4. Remove the brake line from [...]

[Read more →]


Dodge Ram Truck 2500/ 3500 5.9L Turbo Diesel ETB, ETC Engine Idendification

December 10th, 2010 · No Comments

General precautions
Disconnect battery ground cable.
Do NOT turn crankshaft or camshaft with timing gear(s) removed.
Remove glow plugs to ease turning engine.
Turn crankshaft in normal direction of rotation (unless otherwise stated).
If fitted: Mark position of crankshaft position (CKP) sensor before removal.
Do NOT turn crankshaft via camshaft or other gears.
Observe all tightening torques.
Check diesel injection pump timing after [...]

[Read more →]


Dodge Sprinter 2007-2008 XSVI-1784-NAV Installation Instructions

December 10th, 2010 · No Comments

In the Dodge vehicle listed above there are no 12 volt accessory wires currently in the factory harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio. The XSVI-1784-NAV is designed to provide a 12 volt 10 amp switched accessory output along with [...]

[Read more →]




?>