Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

How to disconnect the Speedometer on 2007 Chevrolet Tahoe?

January 2nd, 2011 · No Comments

I wanna know how 2 disconnect the speedometer. Not from the transmission but from the back of the instrument cluster… Wich wires do I need 2 cut in order 2 do this?

[Read more →]


How to change brake pads light to go away on a 1999 Cadillac Seville STS?

December 28th, 2010 · No Comments

It’s really annoying. I put in new brake pads, but I didn’t change the sensors and I’m not going to because they are stupid expensive for a feature thats pretty unneeded. Is there any way to keep this light off for good? It comes on every time I turn on the car and I have [...]

[Read more →]


Audi Climate Control LCD Rebuild Kit

November 9th, 2010 · No Comments

Please read and become familiar with these instructions before performing the actual repair. The LCD panel is fragile and can be damaged if incorrectly installed. Installation is very simple and straightforward. Many color photos are included to ensure a trouble free installation. Place several paper towels on your work surface so as not to scratch [...]

[Read more →]


Install OEM HID Lights in your Mustang

November 2nd, 2010 · No Comments

Be aware that this does not replace factory instructions or manuals for service work, but is a free *how-to* following the basic steps that were done on our own in-house car to make the 2008+ factory HID headlamps work on our 2005 GT that originally was not equipped with these headlights. It is worth what [...]

[Read more →]


Mitsubishi Eclipse Electric Fan 325 fits to 1995-1999 Original Radiator

September 18th, 2010 · No Comments

1. Remove the existing electric fan.
2. Cover the ends of the stock electric fan control wires with vinyl electrical tape to seal out the moisture, and secure wires to the frame so they will not contact other moving parts. These leads will not be used with the FAL electric fan.
3. Attach the mounting brackets to [...]

[Read more →]


Magna Charger GM 5.7 1997-2003 Corvette Installation Manual

September 1st, 2010 · No Comments

Please take a few moments to review this manual thoroughly before you begin work, for a few reasons:
1. A quick parts check to make certain your kit is complete (See shipper parts list in this manual). If you discover shipping damage or shortage, please call our office immediately.
2. Take a look at exactly what you [...]

[Read more →]


1992-1995 Honda Civic EG & 1994-2001 Acura Integra DC WHEG01 K-series Conversion Harness Install Guide

June 30th, 2010 · No Comments

Notes before installation: Type R engine harnesses are for a RHD car. If your car is not RHD, consider extending the ECU connectors for easier installation. Soldering joints are better than plastic connectors. Use heat shrink over any and all soldered wires. Electrical tape is not a proper cover for an open wire!!
Installation
1. Begin by [...]

[Read more →]


01-05 Mazda Miata Base (5psi) Supercharger Kit Installation Instructions

April 24th, 2010 · No Comments

The KraftWerks Mazda Miata Supercharger kit is designed and engineered to install with ease. If you are a competent mechanic with a good set of tools the installation will be relatively simple. This is a general installation guide for the KraftWerks Mazda Miata kit however each installation may vary slightly. Please keep these key factors [...]

[Read more →]


99-Up Ford Model: 8005 & 8005TK Superduty F250, F350, F450, F550 Installation Instructions

January 13th, 2010 · No Comments

Tools required for the installation are: 7/16″, 5 mm & 9/32″ sockets, a small screw driver, electrical tape and a sharp tool for cutting a hole for the in/out switch. Model 8005TK will also require a volt meter.
REMOVAL OF EXISTING MIRROR:
1. Remove the trim panel on both doors (note – Ford doors do not have [...]

[Read more →]


2004 Mazdaspeed Miata Short Ram System Installation Instructions

September 24th, 2009 · No Comments

Installation of the AEM Short Ram Intake System.
a) When installing the Short Ram Intake System, DO NOT completely tighten the hose clamps or mounting tab hardware until instructed to do so later in these instructions.
b. Install the supplied 1.75” to 2.25” reducing elbow onto turbo inlet with pipe and clamps as shown.
c. Assemble the supplied [...]

[Read more →]




?>