Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

How long does it take to rebuild an engine of a 1992 Chevrolet Cavalier?

January 1st, 2011 · No Comments

I seized the engine on my car on Saturday and I was curious how long it would take to rebuild it.

[Read more →]


How much will it cost to replace the engine in a 1998 Chevrolet Cavalier?

December 31st, 2010 · No Comments

I think that I can get the motor myself at cherry auto parts for around 700.00.I was just wondering if I do it that way how much it will cost to have someone put it in for me.Also, the air doesn’t work, so any ideas on how much that will cost and what might be [...]

[Read more →]


How do I remove key that is stuck in ignition on 1996 Cadillac Eldorado?

December 27th, 2010 · No Comments

I have a 1996 Cadillac Eldorado, key seems to be stuck in ignition. Key will turn to start car, but will not turn to “Lock” position to remove key. Have tried turning steering wheel both ways, what next?

[Read more →]


How people write reviews of new cars when these cars are not at dealers yet?

December 25th, 2010 · No Comments

Personally I don’t care about reviews for cars that are not available yet. The reason is that I don’t trust what someone says, for example in a review by autoweek television they said that the Ford Edge was not well tough out and so on putting it down. Bull crap I tested one and I [...]

[Read more →]


How to start a 1990 Cadillac El Dorado?

December 25th, 2010 · No Comments

We have been trying to start a ‘90 Caddy El Dorado, but it won’t budge. It has a special mechanism where the alarm locks the ignition switch, but it’s been so long since we’ve used it that we forgot the trick that gets it to disengage. If anyone knows how to disengage it, please post [...]

[Read more →]


How do I program a second key for a 2005 Nissan Altima?

December 21st, 2010 · No Comments

I just purchased a 2005 Altima and it only came with one key and fob. I bought a blank online, had it cut and now want to use it on my car. I have read varying reports online that it is possible and others that say the opposite. If it is possible without forking over [...]

[Read more →]


Dodge 6.7L Cummins PMT Installation Instructions

December 4th, 2010 · No Comments

This is a temporary document that describes the steps needed to install the dodge 6.7L Cummins file onto the PMT. This document will be consolidated into the complete PMT installation manual as soon as development is complete for the GM 6.6L duramax LMM and 6.4L Ford Powerstroke applications are also complete.

[Read more →]


Custom Door Handles Lead Filling Fiberglass Prep

November 23rd, 2010 · No Comments

Mld-’90s Mazda Miata exterior door handles are normally mounted horizontally, but Paul turned this Miata handle 90 degrees, allowing it to be mounted in the lower portion of the door. This is a much lower mounting point than the original Ford handle, providing easier access from ground level. Plus, this position allows the door handle [...]

[Read more →]


Ford Probe Crankshaft Sensor Location

November 21st, 2010 · No Comments

The Ford Probe was a car produced from 1989 to 1997 in the United States with two-door. Throughout the duration of the Probe’s development, all four-cylinder engine models had the crankshaft position sensor located in the same area of the engine. The role of this sensor is to detect the position of the crankshaft, sending [...]

[Read more →]


Install OEM HID Lights in your Mustang

November 2nd, 2010 · No Comments

Be aware that this does not replace factory instructions or manuals for service work, but is a free *how-to* following the basic steps that were done on our own in-house car to make the 2008+ factory HID headlamps work on our 2005 GT that originally was not equipped with these headlights. It is worth what [...]

[Read more →]




?>