Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

Chevrolet C-5 Corvette Header System Installation Instructions

January 2nd, 2011 · No Comments

Stock System Removal
Under the Hood: Place the vehicle up on jack stands or a hydraulic lift to provide access to the bottom of the vehicle. For safety and to protect you car’s electrical system, remove the ground cable from the negative battery terminal.
Carefully remove the fuel rail covers, from both the top left and right [...]

[Read more →]


How to check the fuel pressure on Chevrolet s10?

January 1st, 2011 · No Comments

I have a 99 chevy s 10 with a 4.3 liter v6, it has a throttle body. I need to figure out how to check the fuel pressure and make sure the fuel pump is what is bad.

[Read more →]


Nissan SR20 & KA24D Fuel Rail Fits 50LB/HR Injectors

December 24th, 2010 · No Comments

The use of this part is for off-road use only and is designed for installation only by a qualified technician. It is assumed that the installer is building a custom race engine and is aware of all procedures needed to safely complete an installation of this type. If this assumption is not correct do not [...]

[Read more →]


1989 Nissan 300ZX Intake Manifold Installation

December 24th, 2010 · No Comments

Removal 1. Release fuel system pressure. Disconnect battery and drain cooling system. Disconnect vacuum and coolant lines attached to intake manifold and label accordingly. Remove throttle linkage. Remove collector cover and collector. 2. Disconnect fuel line and components that interfere with removal. Remove intake manifold bolts using removal sequence. Remove intake manifold and fuel injector [...]

[Read more →]


1996 Nissan Altima GLE Timing Chain

December 21st, 2010 · No Comments

TIMING CHAIN for Nissan Altima GLE Installation Procedure:
CAUTION: If cylinder head is installed and timing chain is disconnected, DO NOT rotate camshaft or crankshaft; valves will contact pistons, resulting in bent valves.
NOTE: Procedure includes cylinder head removal; however, it may not be necessary to remove cylinder head.

[Read more →]


2000 Nissan Altima SE Timing Belt Installation

December 18th, 2010 · No Comments

Removal
1. Release fuel pressure. See FUEL PRESSURE RELEASE. Drain coolant from radiator and cylinder block. Drain engine oil. Disconnect all necessary coolant hoses, electrical connectors, vacuum hoses, fuel lines and control cables.
2. Remove front exhaust pipe. Remove air injection valve pipe. Remove intake air duct. Remove radiator fan and shroud. On Frontier and Xterra, remove [...]

[Read more →]


97-00 Dodge Crankshaft Position (CKP) Sensor

December 13th, 2010 · No Comments

The crankshaft position sensor generates pulses and sends them to the PCM. The PCM interprets this input signal to determine the crankshaft position (and engine speed). With this and other information, the engine controller determines injector sequence and ignition timing. The sensor is a hall-effect device combined with an internal magnet. It is sensitive to [...]

[Read more →]


User Manual Honda B16/B18 Supercharger kit

November 14th, 2010 · No Comments

This manual is written for the Honda CRX 1991 (Euro, JDM) B16A1, but also applies to other Honda cars equipped with the B16/B18 engine. The manual consists of four parts:
- Installation manual
- Performance issues
- Tuning guide
- Engine building

[Read more →]


Flyin’ Miata Fuel Rail Installation Instructions

August 18th, 2010 · No Comments

Congratulations on purchasing the FM Fuel Rail! We’re confident that this high quality piece will help ensure the safety and performance of the engine in your Miata. Following are instructions that will help you safely install this piece.
1. The fuel system first needs to have its pressure relieved. First, find the relay that’s pictured to [...]

[Read more →]


1999-2000 Honda Civic Si Racing Intake Manifold

June 30th, 2010 · No Comments

Before installation, thoroughly flush manifold with water and let completely dry. Disconnect battery and drain coolant before beginning. Mark and identify all hoses and valves. Check condition of all hoses, gaskets and O-rings. Replace as needed. Do not smoke during the work. Keep open flames away from work area. Some pieces are not included in [...]

[Read more →]




?>