Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

Electrical System for Towing Hitch

May 15th, 2011 · No Comments

Install electrical kit
1. Disconnect battery.
2. Remove the following covers and panelling, as necessary:
• In the boot – Boot floor cover – Loading sill cover – Left side panel
• Along the right hand side of the vehicle – Side panel rear (Cabrio) – Scuff plates, driver’s side – Right panelling by the steering column – Fuse [...]

[Read more →]


Replace a fuse in 1996 Chevrolet Blazer to get blinker working

December 29th, 2010 · No Comments

I need to replace a fuse in my 1996 Chevrolet Blazer to get my blinker working again. How do I know which one to replace? I do not have an owners manual and there is no guide in the fuse box any longer. Can someone direct me to a link online where I can [...]

[Read more →]


How do I tell if I have anti-lock brakes on my 1984 Cadillac?

December 28th, 2010 · No Comments

I have a bad master brake cylinder so I went to auto zone and got a new one, I wasn’t sure if I had anti-lock or not so I got the one that wasn’t because I know that I can push on the brakes and they’ll lock up, but when I got home and compared [...]

[Read more →]


The fan doesn’t work on my 1987 Cadillac Deville?

December 26th, 2010 · No Comments

I tried to check the fuse but it doesn’t have on in the fuse box. how can i fix it?
- There may be nothing wrong with the fan motor or fuse. The temperature sensor may be bad.

[Read more →]


How can I disable the DRLs on my 2003 Cadillac Seville?

December 25th, 2010 · No Comments

Just bought an 03 Seville and can’t abide the running lights. I found the DRL relay in the fuse box, but I know that there are usually wires to snip, etc, and I’m afraid of fooling with the wrong ones. Any advice appreciated!

[Read more →]


How to fix the turn signals on 95′ Nissan Pickup?

December 20th, 2010 · No Comments

I have a 95 Nissan Pickup w/ V6 and 5spd. Recently the turn signals quit working. I replaced the turn signal switch and checked all the fuses and bulbs and they checked fine. I also replaced the flasher above the fuse box and still no luck. Dont know what else to check.

[Read more →]


Dodge Sprinter 2007-2008 XSVI-1784-NAV Installation Instructions

December 10th, 2010 · No Comments

In the Dodge vehicle listed above there are no 12 volt accessory wires currently in the factory harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio. The XSVI-1784-NAV is designed to provide a 12 volt 10 amp switched accessory output along with [...]

[Read more →]


98-02 Dodge Cummins Fuel Supply Pressure Warning Light Install Instructions

December 5th, 2010 · No Comments

Dodge Fuel Supply Pressure Warning Light Installation:
1. Remove trim panel by gently pulling around edges until it comes free. One screw holds the upper right hand corner. Open the power outlet door to remove screw. Shifter will have to be in 1st gear position on automatics to remove panel from vehicle.
2. Using a 5/16” drill [...]

[Read more →]


2003 Mazda Truck MPV Ignition Coil Service and Repair

November 25th, 2010 · No Comments

IGNITION COIL REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. LH: Remove the plug hole plate. (See TIMING CHAIN REMOVAL/INSTALLATION). RH: Remove the dynamic chamber. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION).
3. Remove in the order indicated below.
- Connector
- Ignition coil
- Install in the reverse order of removal.

[Read more →]


1998-2000 Ford Ranger, Mazda Pickup Kit SUM-7888300 Installation

November 25th, 2010 · No Comments

This body lift kit should only be installed on vehicles in good working condition. Before installation, the vehicle should be thoroughly inspected for evidence of corrosion or deformation of the sheet metal around the factory body mounts. This body lift kit should not be installed on any vehicle that is suspected to have been in [...]

[Read more →]




?>