Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

Carbureted Victor Jr. & Super Victor LS1 Intake Manifold for GM 5.7L LS1 V8 Engines

February 18th, 2011 · No Comments

The Victor Jr. and Super Victor LS1 Intake Manifolds allow the user to retro-fit any GEN III-based longblock into an early or custom vehicle, using a carburetor. These manifolds are intended for use in racing classes where EFI is not desired or allowed. Manifold kit #2908 includes an electronic Timing Control Module, which picks up [...]

[Read more →]


2006-2008 Chevrolet Impala Slide-Out Trunk Tray Installation

January 26th, 2011 · No Comments

1. Attach forward mounting legs to the slide out tray.
• Attach forward mounting legs with provided 8-32 screws and hex nuts to slide track.
• The front legs will be square to the slide tray.
• On the front passenger side of the half tray, passenger side front mounting brackets (CM001394) will attach to the front mounting [...]

[Read more →]


How to replace a water pump on 92 Cadillac Deville

December 29th, 2010 · No Comments

We have a 92 cadillac deville, my husband can replace the water pump he justs need to know if you have to jack the motor a little. Please help before our car blows up!

[Read more →]


A.W.E. Tuning Drive Train Stabilizer

October 30th, 2010 · No Comments

While the install is fairly straight forward, please review these instructions carefully before attempting installation. If you do not feel comfortable installing this kit on your own, contact a professional installer in your area. Installation of this product requires removing various drive train support fasteners from below. Use proper jack stands to support your vehicle [...]

[Read more →]


2010-11 Ford Taurus SHO 3.5L V-6 Intake System Part Number 450-260 Installation

September 11th, 2010 · No Comments

Page 1
Installation step the airaid intake system for Ford Taurus
1. Disconnect the negative battery cable.
A.) Loosen the hose clamps that secure the flexible intake tube to the factory air box and the 90 degree. elbow pipe.
B.) Compress the flexible intake tube and remove it from the vehicle. It will not be re used.
2. A.) Unfasten [...]

[Read more →]


GM & Ford Tailgate Hinge/Trunnion Installation Instructions

March 30th, 2010 · No Comments

41-53 GM Stepside: Install one hinge to the passenger bed side rear stake pocket with two 5/16” hex head bolts, one lock washer, and one nut. The upper bolt threads into a nut welded inside the stake pocket. Leave loose for now. Fit the tailgate onto this hinge. Place the second hinge into the opposite [...]

[Read more →]


1992–1996 Ford F150 RT3 Undercarriage Mounting Instructions

January 28th, 2010 · No Comments

The mounting procedure outlined below covers 1992 – 1996 FORD F150 trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Remove the front bumper. If the truck is equipped with a front stabilizer bar, remove [...]

[Read more →]


1973-1993 DODGE W250 & W350 RT3 Undercarriage Mounting Instructions

January 7th, 2010 · No Comments

The mounting procedure outlined below covers 1973 – 1993 Dodge W250 & W350 trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as follows:
1. Remove the Front Bumper and Front Bumper Mounting Brackets from the Frame Horns. [...]

[Read more →]


1994-Up Dodge RT3 Undercarriage Mounting Instructions

December 5th, 2009 · No Comments

The mounting procedure outlined below covers 1994 & newer 4 X 4 DODGE ū and 1 ton and 1994 – 1996 4 X 4 DODGE ― ton trucks. You will need to refer to the illustrations and familiarize yourself with each of the undercarriage components and their relative position to each other. Then proceed as [...]

[Read more →]


2003 to 2007 Dodge 5.9L Cummins (24-valve) Charge Air Cooler Assembly Owner’s Manual

December 3rd, 2009 · No Comments

Intercooler Assembly Installation:
1. Disconnect the negative battery cables from both batteries
2. Disconnect the inlet air temperature/ pressure sensor connector located on the air box cover. the connector is shown in Figure 1.
3.Remove the nut that fastens the air filter housing to the radiator cross brace.
4. Loosen the hose clamp that secures the air inlet duct [...]

[Read more →]




?>