Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

Audi A4 B6/8E 5 Speed Short Shifter Installation Manual

May 13th, 2011 · No Comments

Start by ensuring that the engine is switched off and the hand brake is set.
Step 1: Removal of console cover plate and shift knob.
To remove the cover plate, open the ashtray and pull up on the front of the cover. Do the same for the rear of the cover by lifting from within the shift [...]

[

How much is it to fix a heater core for a 1996 Cadillac Deville?

December 24th, 2010 · No Comments

How much is it to fix a heater core for a 1996 Cadillac Deville or the thermastat i don’t know no it was leaking coolant on the passenger side. My mechanic says its the heater core.

[

Nissan GT-R Intake Kit Installation Instructions

December 21st, 2010 · No Comments

In addition to basic tools we highly recommend that you have a quarter drive ratchet with metric sockets, swivel attachment and long extension. We also recommend getting a can of silicone spray lubricant. You should not use petroleum based lubricants such as WD-40 as this may damage the connectors.

[

2006 Dodge Dakota/Mitsubishi Raider Air Charger P/N. 63-1546

December 11th, 2010 · No Comments

1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Loosen the hose clamp at the throttle body and the air box mounting nut and then disconnect the crank case vent hose from the inline fitting.
3. Disconnect the stock intake tube from the intake plenum and lift to remove the air box [...]

[

Bomz Racing 00-05 Dodge Neon SOHC Cold Air Intake Installation Guide

December 6th, 2010 · No Comments

Removal of Factory Intake
Turn the ignition OFF and disconnect the vehicle’s negative battery cable. Remove the wire loom from retaining clips. Loosen and remove the five airbox retaining bolts then remove airbox lid. Remove the stock air filter. Pull up and remove the fresh air intake from fender well. Remove the four throttle body retaining [...]

[

Nissan 350Z POP-Charger Installation instructions

October 27th, 2010 · No Comments

1.Remove the stock air box and the MAF sensor as an assembly. Using a 10MM socket wrench, remove the single mounting bolt and loosen the hose clamp around the MAF sensor. On the air inlet snorkel, remove the plastic retainer rivet and pull the snorkel away from the air box. Pull up on the air [...]

[

JWT G35/350Z Twin Turbo Fuel Management Unit (FMU) Installation Guide Addendum

October 22nd, 2010 · No Comments

1. Installing the new fuel pump and FMU. Wear eye protection and insure that you are working in a well-ventilated area without open flames, static electricity or spark potentials, as gasoline fumes will be present.
2. Installing the 1/8” nylon FMU signal line. Remove all of the battery compartment covers so you can see the ECU [...]

[

2010-11 Ford Taurus SHO 3.5L V-6 Intake System Part Number 450-260 Installation

September 11th, 2010 · No Comments

Page 1
Installation step the airaid intake system for Ford Taurus
1. Disconnect the negative battery cable.
A.) Loosen the hose clamps that secure the flexible intake tube to the factory air box and the 90 degree. elbow pipe.
B.) Compress the flexible intake tube and remove it from the vehicle. It will not be re used.
2. A.) Unfasten [...]

[

Toyota Celica 1.8L Part Number 57-0502 Installation Instructions

August 29th, 2010 · No Comments

Toyota Corolla 1.6L 16v 116bhp (4A-FE Engine) 1992 – 1997
Disconnect the negative battery terminal from the battery. Carefully disconnect & remove the air temperature sensor from the air box lid. (Fig. 1) Unclip and remove the intake hose from the throttle housing. Unclip and remove the air box lid assembly from the vehicle. Unscrew and [...]

[

2009+ Nissan 370Z Dual Pop-Charger Air Intake System Installation Instructions

June 14th, 2010 · No Comments

1. Remove the original air filter boxes by loosening the hose clamp, unplugging the electrical plug, and removing the air box retaining bolt. There is only one bolt securing each air filter box and they will release from the car by firmly pulling up on them after the single bolt is removed.
2. Transfer the MAF [...]

[