Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

How to change out the headlights on a 2006 Nissan Titan?

December 20th, 2010 · No Comments

I just bought some brighter lights for my Titan and I can’t figure out where to start on switching them out with the old ones. It looks like I’m going to have to take a lot of it apart to get to them. Anybody able to help me with this?

[Read more →]


2006 Dodge Dakota/Mitsubishi Raider Air Charger P/N. 63-1546

December 11th, 2010 · No Comments

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Loosen the hose clamp at the throttle body and the air box mounting nut and then disconnect the crank case vent hose from the inline fitting.
3. Disconnect the stock intake tube from the intake plenum and lift to remove the air box [...]

[Read more →]


Dodge Ram 2500-3500 Cummins Intake Kits Installation

December 7th, 2010 · No Comments

Step 1. Complete kit with parts.
Step 2. Complete stock intake.
Step 3. Loosen clamp at turbo inlet and remove top half of filter box and filter element.
Step 4. Remove lower half of filter box, unscrew 3 inserts and transfer inserts to new filter housing.
Step 5. Remove inner fender brace screw and ground wire screw. Trim wire [...]

[Read more →]


Bomz Racing 00-05 Dodge Neon SOHC Cold Air Intake Installation Guide

December 6th, 2010 · No Comments

Removal of Factory Intake
Turn the ignition OFF and disconnect the vehicle’s negative battery cable. Remove the wire loom from retaining clips. Loosen and remove the five airbox retaining bolts then remove airbox lid. Remove the stock air filter. Pull up and remove the fresh air intake from fender well. Remove the four throttle body retaining [...]

[Read more →]


2003 CR-V Body Side P/N 08P21-S9A-100 Cladding Installation Instructions

November 16th, 2010 · No Comments

Installing the Front Fender Piece
1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons.
2. Disconnect the negative cable from the battery.
3. Remove the one bolt and three clips that fasten the left front inner fender, and pull the inner fender out in the direction shown. [...]

[Read more →]


2005 CR-V Front Splash Guards P/N 08P08-S9A-100A Installation

November 10th, 2010 · No Comments

Installation procedure:
These instructions show the left splash guard being installed. The same procedure applies to installing the right splash guard.
1. Make sure the area to be covered is clean.
2. Turn the steering wheel all the way counterclockwise.

[Read more →]


1995-2000 Honda CRV/Odyssey Signal and Marker Lights Repair Information

May 31st, 2010 · No Comments

REMOVAL & INSTALLATION Front Turn Signal and Parking Lights CRV MODELS AND V6 ODYSSEY MODELS
1. Turn the steering wheel in the opposite direction from which the bulb is to be removed.
2. Using a flat blade screwdriver, remove the fasteners securing the inner fender behind the headlight and pull back on the
inner fender liner.
3. Remove the [...]

[Read more →]


Bomz Racing 03-05 Mazda 6 L4 Cold Air Intake Installation Guide

May 2nd, 2010 · No Comments

Removal of Factory Intake
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Disconnect the mass air sensor electrical connection.
3. Disconnect the vacuum switch electrical connection.
4. Disconnect the crank case vent hose from the hard line.
5. Loosen the clamps at the throttle body and at the mass air sensor, then pull the stock [...]

[Read more →]


2005 Ford Expedition 5.4L Airaid Intake System Instructions

April 9th, 2010 · No Comments

1. Disconnect negative battery cable. Grasp intake tube and sharply lift up and away from airbox.
2. Grasp large oval section of intake tube and pull up and away from inner fender well, and remove entire intake tube. (Note: Intake tube is held in with rubber grommets, no bolts.)
3. Remove 13mm nut on power steering reservoir [...]

[Read more →]


2005-06 Ford 4WD Super Duty F250-350 4 1/2″ Coil Spring Suspension System Instructions

January 18th, 2010 · No Comments

FRONT OF VEHICLE – DISASSEMBLY AND ASSEMBLY
1. Park vehicle on level, hard (concrete) surface.
2. Block the rear wheels of the vehicle to prevent vehicle from moving in either direction and set parking brake.
3. Remove the track bar bolt 30 mm (save for later use) on the driver side of the frame mount (Fig.1), and the [...]

[Read more →]




?>