Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

2011 Nissan Juke 1.6L-T Synchronic Diverter Valve Kit Installation Instructions

September 26th, 2011 · No Comments

1. Remove the top engine cover by pulling the taps where the red arrows are indicated in the picture
2. Using a pair of pliers, loosen and pull back the hose clamp highlighed in the picture
3. Gently detach the OE recirculation hose from the OE By-Pass Valve
4. Push the small hose clamp back and detach the [...]

[Read more →]


PowerMax Diesel Upgrade For Cummins Engines

December 15th, 2010 · No Comments

Prior to the PowerMax Kit installation, be sure that the vehicle is parked on a level surface and the engine is cool. Engine fluids and components can be extremely hot following normal vehicle operation. Avoid direct contact of engine fluids or components with your skin; may cause personal injury.

[Read more →]


Dodge/Jeep Jet Performance Module Instructions

December 9th, 2010 · No Comments

The Jet Performance Module is designed to enhance the performance and drivability of your vehicle. By optimizing the air/fuel ratio, ignition advance and various other parameters. The Jet Module retunes your engine for maximum performance.
JET STAGE 1 MODULE:
The Jet Stage 1 Module is optimized for stock vehicles. Minor bolt on modifications such as free flow [...]

[Read more →]


Auxiliary Fuel Tank Installation for Chevy, Dodge, or Ford

December 9th, 2010 · No Comments

Instructions for: Fuel Tank Installation (AFC-1 = 99-06 Ford & LB7 Duramax), (AFC-2 = LLY & LBZ Duramax), (AFC-3 = 2000-2006 Dodge), (AFC-4 = 2008 Ford). On 2004 GM diesel pickups, check the pickup’s Vehicle Identification Number (VIN). Your pickup will have an LB7 engine if there is a “1” in the eighth digit of [...]

[Read more →]


1994-2002 Dodge Front 7-8″ Lift Kit Installation Instructions

December 8th, 2010 · No Comments

Dodge Front Kit Installation Steps:
1. Before you remove anything off the truck, measure the pinion angle on the bottom of the differential. Make sure to record the measurement here. Once the kit is installed, it is required to put the axle back to this measurement. This will keep the correct caster and camber.

[Read more →]


09 & Up Dodge 4WD 1500 2.5″ FR / 3/4″ RR Kit

December 6th, 2010 · No Comments

Under hard acceleration in 4×4 high, stock Dodge Ram’s often have a front end vibration or shutter. This vibration or shutter exist due to the design of the motor and differential mounts and is inherent in the vehicle. This vibration or shutter may be more pronounced after a leveling kit is installed due to additional [...]

[Read more →]


2007-2009 Dodge 6.7L Cummins Banks Split Dual Monster Exhaust System Quad-Tip

December 6th, 2010 · No Comments

This manual is for use with system 49767
1. Before starting work, familiarize yourself with the installation procedure by reading all of the instructions.
2. The exploded view (Figure 1) provides only general guidance. Refer to each step and section diagram in this manual for proper instruction.
3. Throughout this manual, the left side of the vehicle refers [...]

[Read more →]


1998 Dodge RAM Pickup Part Number DG-70-98 Installation Instructions

December 6th, 2010 · No Comments

STEP 1. Open up the power outlet door and locate and remove one (1) Phillips head screw using your # 2 Phillips screwdriver . Set screw aside. Open up both the cup holder door and the ashtray door. Remove the dash trim bezel that surrounds the radio and climate control and extends across the instrument [...]

[Read more →]


2006-2007 Dodge Charger 4K56C06 Installation Instructions

December 5th, 2010 · No Comments

B-Pillar Bracket Installation
A. Begin by removing the middle B-pillar section.
This will be reinstalled after drilling holes into the cover. Cut the template where indicated and align with the seat belt relief (fig. 2). Use the template provided as a guide for drilling 1” holes. Be sure to remove the sound insulation located inside the cover [...]

[Read more →]


South Bend Ford/Dodge DD Installation Instructions

December 5th, 2010 · No Comments

Removal and Installation
Removal
1. Disconnect battery negative cable.
2. Shift transmission into Neutral.
3. Remove screws attaching shift boot to floor pan. Then slide boot upward on the shift lever.
4. Remove the bolts holding the shift tower to the isolator plate and transmission gear case.
5. Remove the shift tower and isolator plate from the transmission gear case.
6. Raise [...]

[Read more →]




?>