Automotive Manual, Car Parts and News

REMOVAL INTERFERENCE ENGINE. In the event of timing chain failure, it is probable that valve to piston damage has occurred. A compression test should be carried out on all cylinders before removing the cylinder head.
1. Remove engine under cover.
2. Drain engine coolant from cylinder block.
3. Remove: radiator, – all drive belts, – cooling fan and [...]

[Read more →]

On some models, engine is equipped with a timing belt and timing chain. Inspect timing chain when replacing timing belt.
Removal
1. Remove the engine cover. 2. Remove right front wheel. 3. Remove right side cover. 4. Set the jack to the engine oil pan. Remove the engine mount bracket. Remove the stay plate. 5. Temporarily loosen [...]

[Read more →]

This pdf covers the timing belt guide for HYUNDAI 1.8L & 2.0L 4-Cylinder – 1996-04 (Except Sonata & 2004 Elantra).
Removal 1. Remove all drive belts and drive pulleys from crankshaft and water pump. Remove generator bolt, if necessary. Remove crankshaft pulley and water pump pulley. 2. Remove timing belt covers and gaskets, noting bolt lengths [...]

[Read more →]

Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of [...]

[Read more →]

This document covers the steps of Timing Belt installation for 1995 Isuzu Trooper LS
Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts. 2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil [...]

[Read more →]

REMOVAL SERVICE POINT TIMING BELT REMOVAL
CAUTION: The crankshaft should always be turned only clockwise. 1. Turn the crankshaft clockwise (right turn) to align each timing mark and to set the number 1 cylinder at compression top dead center. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry [...]

[Read more →]

Removal (1994-97 3.0L V6) 1. Disconnect negative battery cable. Remove coolant reservoir. Raise and support vehicle. Remove right side front wheel. Remove right lower engine cover. Remove accessory drive belts. 2. Remove engine stabilizer rod, engine mounting bracket and right engine mount brace, located near timing belt cover. Remove the alternator bracket for access to [...]

[Read more →]

This manual covers the removal and installation of timing belt for honda passport lx. Removal
1. Disconnect negative battery cable. Remove air cleaner assembly. Remove upper fan shroud. Remove cooling fan assembly. Remove all accessory drive belts.
2. Remove fan pulley assembly. Remove crankshaft pulley bolt. Using Puller (J-8614-01) or equivalent, remove crankshaft pulley. Remove oil cooler [...]

[Read more →]

B.P.T. recommends a qualified mechanic install these pulleys.
1. Loosen water pump bolts.
2. Remove belt. Tensioner is accessible from above. Caution with pinch points.
3. With transmission in first gear and hand brake applied, remove harmonic balancer bolt. An impact wrench will be required with automatic transmission. Remove harmonic balancer using a 3-prong balancer remover. Remove water [...]

[Read more →]

Parts Needed: New Crank pulley Bolt (Ford part # F5RZ-6A340-B)
1: Verify that your kit has all the parts included. The kit comes complete with a smaller iron crank pulley, an oversized water pump pulley, and the instructions.
2: Remove the air intake, this step isn’t required but makes for a much easier installation when you are [...]

[Read more →]