Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

2006 Chevrolet Corvette Z06 Axle Back System With Single Pro-Series 4.0″

January 6th, 2011 · No Comments

Factory Exhaust System Removal:
1. Unbolt the rear sway bar brackets from the rear cross member using an 18mm socket on the top and bottom bolts. A 15mm wrench will be needed to hold the lower bolt from turning while the nut is removed. (See Fig. A). Do not remove lower bolt from suspension.

[Read more →]


2010 Chevrolet Camaro Exhaust System Installation

December 29th, 2010 · No Comments

This Borla Performance Cat-back™ Exhaust System (Part number 140280, 140281) has been designed for 2010 Chevrolet Camaro equipped with a 6.2L V-8 engine and automatic or manual transmissions. Borla Performance Cat-back™ Exhaust System (part number 140282) has been designed for 2010 Chevrolet Camaro equipped with a 3.6L V-6 engine with an automatic or manual transmission.

[Read more →]


2008 Subaru Impreza WRX Hatchback Exhaust System Installation

November 20th, 2010 · No Comments

Borla Performance Rear Section Exhaust System (Part number 11760) has been designed for the 2008 Subaru Impreza WRX Hatchback equipped with a 2.5L opposed 4 cylinder engine, all-wheel drive and automatic or manual transmissions.
Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners [...]

[Read more →]


2007 Subaru Impreza Exhaust System Installation

November 16th, 2010 · No Comments

Borla Performance Cat-Back™ Exhaust System (Part number 140263) has been designed for the 2007 Subaru Impreza equipped with a 2.5L opposed 4 cylinder engine, all-wheel drive and automatic or manual transmissions.
Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a [...]

[Read more →]


2007 Mazda Speed 3 Exhaust System Installation

April 21st, 2010 · No Comments

Borla Performance Cat-Back™ Exhaust System (Part number 140254) has been designed for the 2007 Mazda Speed 3 equipped with 2.3L Turbocharged 4 cylinder engine, front-wheel drive and a manual transmission. Original Exhaust System Removal
Note: With a used vehicle, we suggest a penetrating spray lubricant to be applied liberally to all exhaust fasteners and allowing a [...]

[Read more →]


2003 Ford F250, F350 6.0L Diesel Dynomax Kit: 19439 Installation Instructions

January 26th, 2010 · No Comments

Read all instructions before starting any work.
1. It is suggested to lower or completely remove the spare tire from under the vehicle. This will help in the removal of the original equipment (OE) exhaust system and with the installation of the DynoMax exhaust kit.
2. Remove the existing exhaust system assembly from the vehicle. Lubricate the [...]

[Read more →]


2006-2008 Dodge Ram 1500 Exhaust System Installation

December 27th, 2009 · No Comments

Never work on a hot exhaust system. Serious injury in the form of burns can result If the vehicle has been in use and the exhaust system is hot, allow vehicle to cool for at least 1 hour. Always wear eye protection when working under any vehicle. Note: It is our recommendation that you use [...]

[Read more →]


2009 Nissan 370Z Exhaust System Installation

November 25th, 2009 · No Comments

By installing your Borla Performance Exhaust System, you indicate that you have read this document and you agree with the terms stated below. It is the responsibility of the purchaser to follow all installation instruction guidelines and safety procedures supplied with your Borla Performance Exhaust System
Borla Performance Industries assumes no responsibility for damages occurring from [...]

[Read more →]


2002-2005 Nissan Altima Exhaust System Installation

November 19th, 2009 · No Comments

This Borla Performance Cat-Back™ Exhaust System (Part number 140105) has been designed for 2002-2005 Nissan Altima equipped with a 3.5L V-6 engine and automatic or manual transmissions. Borla Performance Industries recommends that an exhaust shop or professional after market parts installer, who has all the necessary equipment, tools and experienced personnel needed for proper installation, [...]

[Read more →]


BMW E46 M3 2001- AA Short Shifter Instructions

October 12th, 2009 · No Comments

NOTE: If you have a lighted gearshift knob, do this first !!!
-At the base of the gear lever is a shift boot surrounding the lower shaft.
-Remove the shift boot by detaching the shift boot base from the console area, it is snapped in at the four sides.
-Locate the lighted knob wire that comes from the [...]

[Read more →]




?>