Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

2005-up Chevrolet Cobalt/Pontiac Pursuit TWM Performance Short Shifter Installation Manual

December 31st, 2010 · No Comments

It is preferable to park on a flat surface, as you may have to engage and disengage the hand brake and shift from gears to neutral. If you cannot do so and are obliged to install the short shifter on a slightly inclined surface, place wooden blocks in front or behind the wheels to prevent [...]

[Read more →]


How do i remove spoked hubcaps from a 1988 Cadillac Deville?

December 25th, 2010 · No Comments

Lost tool to remove where can I find one?
- You need a hub cap key. from 1981-1989 go to a junk yard and purchase one. it has to be the same kind of a car though.

[Read more →]


How do I replace the front brake pads on a 1984 Cadillac Deville?

December 25th, 2010 · No Comments

So far I have lifted the car, taken the tire off, taken those two long bolts out, put that little clip from the old pad on to the new pad and put both pads in the thing that holds them. But it seems that the two pads are too thick to fit over the rotor. [...]

[Read more →]


2009-up Dodge Challenger Hurst Billet Comp/Plus Shifter

December 8th, 2010 · No Comments

This shifter is constructed of a solid billet steel and chrome plated upper stick, billet aluminum transmission carrier, and billet stainless steel adapter, lower stick, pin, and Energy Suspension® polyurethane bushing housing. You can expect reduced shift throw (over 30%), increased strength and better, firmer, yet smoother and more precise feel thanks to extremely tight [...]

[Read more →]


350Z Engine Control Unit (ECU) Removal/Re-Install

October 22nd, 2010 · No Comments

Tools require for ECU removal and re-installing.
1. 10 mm socket and ratchet (or equivalent)
2. Philip (cross) screw driver
3. Flat head screw driver
Before you start lower your driver and passenger side window down about 1-2 inches. You can lower it more, but at the very minimum 1-2 inches. This is done so when you disconnect your [...]

[Read more →]


96 BMW 3 Series/M3 (E36) Front Midrange / Tweeter Installation Instructions

July 26th, 2010 · No Comments

Tools Required for BMW Front Midrange / Tweeter Installation: (All the below are readily available at your local auto parts store) • Panel Removal Tool • Torx T20 screwdriver • 8mm socket wrench • Small, Straight Pick Tool • Hot Glue Gun w/Glue Sticks We’ve broken down our instructions into each task so that you [...]

[Read more →]


1997 Ford Truck F 150 2WD Pickup Timing Chain Service and Repair

June 1st, 2010 · No Comments

1997 Ford Truck F 150 2WD Pickup V8-5.4L SOHC VIN L Vehicle Level Engine, Cooling and Exhaust Engine Timing Chain Service and Repair Installation
Ford does not provide a procedure to align the timing components without the OE tools specified. 1. Compress the tensioner plunger, using an edge of a vise. CAUTION: Timing chain procedures must [...]

[Read more →]


2004 Mitsubishi Lancer O-Z Rally Timing Belt Installation

May 22nd, 2010 · No Comments

REMOVAL SERVICE POINT TIMING BELT REMOVAL
CAUTION: The crankshaft should always be turned only clockwise. 1. Turn the crankshaft clockwise (right turn) to align each timing mark and to set the number 1 cylinder at compression top dead center. 2. Loosen the tension pulley fixing bolt. 3. Place a screwdriver against the tensioner pulley and pry [...]

[Read more →]


2004 Hyundai Santa Fe Timing & Counterbalance Shaft Belts Installation

May 22nd, 2010 · No Comments

This application is an interference engine. Do not rotate camshaft or crankshaft when timing belt is removed, or engine damage may occur.
Removal
CAUTION: DO NOT rotate engine counterclockwise (as viewed from timing belt end of engine). If reusing timing belt, place reference mark on timing belt to indicate direction of rotation before removing.
1. Remove drive belts [...]

[Read more →]


1995 Mercedes Benz E 320 Cabriolet (124 Chassis) Timing Chain Replacement and Riveting

May 16th, 2010 · No Comments

Proceeding work
Spark plugs removed. Refer to Powertrain Management – Ignition System – Spark Plug
- Service and Repair – Procedures
Replacing and riveting timing chain
NOTE: Numbers in parentheses ( ) indicate a component or tool in the associated
illustration.

[Read more →]




?>