Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

2003 Mazda Truck MPV Ignition Coil Service and Repair

November 25th, 2010 · No Comments

IGNITION COIL REMOVAL/INSTALLATION
1. Disconnect the negative battery cable.
2. LH: Remove the plug hole plate. (See TIMING CHAIN REMOVAL/INSTALLATION). RH: Remove the dynamic chamber. (See INTAKE-AIR SYSTEM REMOVAL/INSTALLATION).
3. Remove in the order indicated below.
- Connector
- Ignition coil
- Install in the reverse order of removal.

[Read more →]


Comfort ZERO1/ZERO2 for Mitsubishi Galant Fortis(CY4A)

August 9th, 2010 · No Comments

The damping force setting is dedicated for comfort-car to keeps comfortable ride while offer drivability with sporty feeling. This is the suspension kit which offers both stylish low-down form and comfortable ride feeling for luxurious comfortable vehicle
-There are type on damping force system; Comfort ZERO1 adopts fixed damping force while Comfort ZERO2 offers 5 steps [...]

[Read more →]


Toyota Transaxle Preload Check and Reassembly

July 26th, 2010 · No Comments

With this worksheet, you will follow the reassembly of a front-drive transmission using the required special tools, make measurements where appropriate, retrieve and apply the needed service information, retrieve and interpret service specification information from the repair manual. Tools and Equipment • Hand Tool Set • Dial Indicator Torque Wrench • Preload Adapter SST (P/N [...]

[Read more →]


03-04 Toyota Corolla Excessive Sulfur Dioxide Odor

July 11th, 2010 · No Comments

Some customers may complain of excessive sulfur dioxide odor on 2003–2004 model year Corolla vehicles under the following conditions:
- Stop and go driving.
- Heavy acceleration.
In order to reduce the sulfur dioxide odor, the Electronic Control Module (ECM) (SAE term: Powertrain Control Module/PCM) fuel cut control logic has been modified and a new catalyst is provided. [...]

[Read more →]


05 Corolla & Matrix 1ZZ-FE Engine No Start Condition

July 9th, 2010 · No Comments

Some 2005 model year Corolla and Matrix vehicles equipped with a 1ZZ–FE engine may exhibit an intermittent “no start” condition. Improvements have been made to the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM) manufacturing process to reduce the possibility of this condition occurring. Please use the following procedure to repair the vehicle.
Inspection Procedure
If [...]

[Read more →]


1994 Toyota Camry DX Timing Belt Removal & Installation

June 1st, 2010 · No Comments

Removal 1. Disconnect negative battery cable. Raise and support vehicle. Remove lower engine cover. On Celica and Camry, remove right front wheel. On all models, lower vehicle. 2. On MR2, remove right hood side panel and cruise control actuator. Remove right rear wheel. On Celica and Camry, remove alternator from engine and secure out of [...]

[Read more →]


Toyota Immobilizer Key Code Reset Service Bulletin

June 1st, 2010 · No Comments

Applicable 4Runner, Camry, Highlander, Land Cruiser, MR2 Spyder, RAV4, Sequoia, & Solara
Immobilizer Reset is a new feature that allows the registration of a new Master Key even if all original Master Keys are lost. Once the Immobilizer system is reset, all previously registered keys will be erased. The Immobilizer Reset function is a 5-step process: [...]

[Read more →]


Rear Drum Brake (4WD and Pre Runner) Removal

October 9th, 2009 · No Comments

1. INSPECT SHOE LINING THICKNESS
Remove the inspection hole plug, and check the shoe lining thickness through the hole. If less than the minimum, replace the shoes. Minimum thickness: 1.0 mm (0.039 in.)
2. REMOVE REAR WHEEL
3. RELEASE PARKING BRAKE LEVER
4. REMOVE BRAKE DRUM
HINT:
If the brake drum cannot be removed easily, do the following steps.
(a) Remove the [...]

[Read more →]




?>