Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

2011 Nissan Warranty Information Booklet

December 23rd, 2010 · No Comments

Both Nissan and your Nissan dealer are dedicated to serving all your automotive needs. Your complete satisfaction with your vehicle and your Nissan dealer are our primary concerns. Your Nissan dealer is always available to assist you with all your automobile service requirements.

[Read more →]


00–01 Nissan Maxima Grille Install Instructions

December 16th, 2010 · No Comments

Step 1: Note these instructions are for both the upper and the lower, so not all steps are applicable of you bought only an upper or a lower grille. The lower will be covered first.
Step 2: Get your tools out, a flat head screwdriver (small), wire cutters, and possibly some pliers or channel locks. Then [...]

[Read more →]


1995-1998 Nissan 240 Radio Replacement

December 16th, 2010 · No Comments

The radio is secured to the entire radio-pocket assembly as one unit, including the plastic panel surrounding the radio. DO NOT pull the plastic panel away from the radio or you will break the plastic panel. The radio and plastic panel must be removed together, as one unit.

[Read more →]


1994-1997 Nissan Maxima No Bose Radio Replacement

December 16th, 2010 · No Comments

These installation instructions are for Nissan Maximas that do NOT have a BOSE radio installed from Nissan. For vehicles WITH the BOSE radio system installed, please consult Document 647022.
Installation Difficulty Ratings
Easy. No advanced skills or specialty tools needed. Basics. Simple tools required. Installs quickly. Intermediate. Requires knowledge of tools, or disassembly of panels. Advanced. Requires [...]

[Read more →]


1998-01 Dodge RAM 1500 Quad Cab Step Bar Assemblies

December 14th, 2010 · No Comments

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against parts list. Read and understand instructions completely before beginning installation.
STEP 2. Install bolt plates into inner support panels near rear body mounts for both passenger and driver side as shown. Use plastic bolt retainer to ensure bolt plate [...]

[Read more →]


2003-2010 Dodge Ram 2500/3500 8″ Long Arm Suspension Install Instructions

December 9th, 2010 · No Comments

STEP Installations of Long Arm Suspension on Dodge Ram 2500/3500
1. Working on the driver side, remove the stock sway bar from the stock sway bar end link. Repeat the procedure on the passenger side. Now remove the stock sway from the stock end links and let the stock sway bar hang. Special note: Step # [...]

[Read more →]


BedLocker Dodge Rambox Installation Instructions

December 8th, 2010 · No Comments

The BedLocker also offers an optional wire harness (part # BL1120) to manually operate the tonneau cover from inside the cab of your truck. This harness is designed to plug into the custom-built electronics control box mounted inside the canister. Thread the plug through the side of the canister and connect it to the grey/violet [...]

[Read more →]


2005 Honda CR-V Roof Rack P/N 08L02-S9A-102 Installation

November 11th, 2010 · No Comments

Installation Procedure for this Roof Rack on Honda CR-V:
NOTE: Be careful not to damage the roof and other finished surfaces of the body when installing the roof rack.
1. Using a flat-tip screwdriver wrapped with a shop towel, remove the four covers from the roof trim.
2. Position the roof rack (marked “Front”) on the front rack [...]

[Read more →]


A.W.E. Tuning Drive Train Stabilizer

October 30th, 2010 · No Comments

While the install is fairly straight forward, please review these instructions carefully before attempting installation. If you do not feel comfortable installing this kit on your own, contact a professional installer in your area. Installation of this product requires removing various drive train support fasteners from below. Use proper jack stands to support your vehicle [...]

[Read more →]


94-98 Ford Mustang 3.8L V6 Throttle Body Spacer

August 7th, 2010 · No Comments

Installation Instructions the Throttle Body Spacer for Ford Mustang:
DISCONNECT NEGATIVE (-) BATTERY CABLE.
Remove air cleaner housing from the throttle body.
Remove (3) bolts and (1) stud from the front side of the throttle body. (Ref. “D”)
Remove (2) bolts from the throttle linkage bracket.
Move throttle body away from intake manifold. Remove old gasket and clean surfaces.
Install power [...]

[Read more →]




?>