Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News


1991-1996 Chevy Corsica Radio Replacement

September 6th, 2010 · No Comments

STEP 1: To remove the radio, the dash panel surrounding the radio and air conditioner controls must be removed. With your hands grab the top of the dash panel above the air vents and pull to unsnap the top of the dash panel. Continue to pull the dash panel until the bottom of the panel […]

[Read more →]


1994-1999 Ford Mustang Radio Replacement Installation

August 7th, 2010 · No Comments

STEP 1: The Ford radio is snapped into the vehicles dash. With the proper tool, known as Ford radio removal keys, the Ford radio can be pulled forward out of the dash. A clothes hanger can be used instead of actual Ford radio removal keys. Cut the clothes hanger and bend 2 pieces in a […]

[Read more →]


03-04 Toyota Corolla/Matrix Fuel Filler Tube Improvement Technical Bulletin

July 11th, 2010 · No Comments

Some 2003 – 2004 Corolla and Matrix 2WD and 2005 model year Matrix 4WD vehicles may exhibit a M.I.L. “ON” condition with DTCs P0440, P0441, P0442, P0446, and/or P0456 stored. An improved fuel filler tube has been developed to correct this condition.
Applicable Vehicle: - 2003 – 2004 model year Corolla and Matrix vehicles equipped with […]

[Read more →]


03-04 Toyota Matrix (1ZZ-FE) M.I.L. On DTC P0420 Technical Service Bulletin

July 11th, 2010 · No Comments

Some 2003 – 2004 model year Matrix vehicles equipped with a 1ZZ–FE engine may exhibit a M.I.L. “ON” condition with Diagnostic Trouble Code P0420 (Catalyst System Efficiency Below Threshold) stored in the Engine Control Module (ECM) (SAE term: Powertrain Control Module/PCM). Follow the repair procedure to reflash the ECM (PCM) and replace the catalytic converter […]

[Read more →]


2006 Honda CR-V EX Front Door Panel Installation

May 31st, 2010 · No Comments

Use the appropriate tool from the KTC trim tool set to avoid damage when prying components. 1. Using a trim tool, pry out the upper portion of the cover (A) to release the hooks (B), then remove the cover. 2. Remove the screws. 3. Driver’s door: Pull the inner handle (A) rearward and out half-way […]

[Read more →]


1990 Nissan-Datsun 300ZX DOHC Heating and Air Conditioning System

May 16th, 2010 · No Comments

Step 1 - Monitor Diagnosis
This step checks all the temperature sensing circuits.
OPERATION
Each time the HI switch is pressed, the code number in the SET section advances one
number and corresponding data with the code number appears in the AMB section.
Each time the LO switch is pressed, the code number reduces by one number and
corresponding data with […]

[Read more →]


Nissan Titan JackRabbits Retractable Hard Truck Bed Covers Installation

May 4th, 2010 · No Comments

The JackRabbit is designed to carry rainwater from the cover into the canister and then out through the drains. Most truck models have standard OE drain holes or plastic/rubber access ports in the front of the truck bed. Check to make sure your truck has the OE drain holes so that drilling into the sheet […]

[Read more →]


Nissan Titan Side Rail Installation Instructions

May 4th, 2010 · No Comments

If your Nissan Titan pickup bed rails do not have utility tracks, install side rails as shown in your TruXedoо Lo Pro Owners Manual.
STEP 1: Insert female clamps, three per side, into utility tracks on Nissan bed rails.
STEP 2: Evenly space and fasten male clamps loosely to female clamps with 3/8” x 1 1/2” […]

[Read more →]


2000-05 Audi Mk1 TT Vent Boost Gauge Kit

May 3rd, 2010 · No Comments

While the install is fairly straight forward, please review these instructions carefully before attempting installation. If you do not feel comfortable installing this kit on your own, contact a professional installer in your area.
Step 1: Remove factory vent by popping it out from the sides with the small flathead screwdriver. Grasp the edge of the […]

[Read more →]


Ford 302 HO Hydraulic Roller Lifter If it Installation Instructions

April 12th, 2010 · No Comments

This kit is designed to allow the installation of hydraulic roller cams in standard Ford 302 HO V8 engines originally equipped with hydraulic roller cams. In order to use this kit, your engine must have two bosses cast into the block (see figure 1 ) in the lifter valley area. These bosses may or may […]

[Read more →]


Search engine terms: remove radio corsica,