Automotive Manual, Car Parts and News

INSTALLATION INSTRUCTIONS:
1. Measure the vehicle from the center of the hub to the fender lip and record this measurement below.
2. Be sure you are working on a level surface. Block the rear tires and raise the front of the vehicle. Support the frame with jack stands.
3. Remove the front wheels.
4. Disconnect the steering linkage and [...]

[Read more →]

FITTING YOUR BOV 300ZX ADAPTOR
Note: Please thoroughly read and understand both these instructions and the fitting instructions supplied with your BOV before commencing this installation.
Step 1. Locate the two boost hoses.
Step 2. Loosen the factory hose clamps securing the boost hoses to the intercooler pipe and throttle body.

[Read more →]

This shifter is constructed of a solid billet steel and chrome plated upper stick, billet aluminum transmission carrier, and billet stainless steel adapter, lower stick, pin, and Energy Suspension® polyurethane bushing housing. You can expect reduced shift throw (over 30%), increased strength and better, firmer, yet smoother and more precise feel thanks to extremely tight [...]

[Read more →]

Step 1. Complete kit with parts.
Step 2. Complete stock intake.
Step 3. Loosen clamp at turbo inlet and remove top half of filter box and filter element.
Step 4. Remove lower half of filter box, unscrew 3 inserts and transfer inserts to new filter housing.
Step 5. Remove inner fender brace screw and ground wire screw. Trim wire [...]

[Read more →]

STEP 1. Remove the contents from the box and check for any damage. Verify all parts against the parts list. Read and understand instructions completely before beginning installation.
STEP 2. Position and hold template on passenger side for square bracket as shown. (FOR TOYOTA, NISSAN, CHEVY S-10, GMC up to ‘94, and MAZDA up to ‘94 [...]

[Read more →]

Tailgate Spoiter installation on Honda CR-V 2010:
NOTE: Be careful not to damage the tailgate and the body paint finish.
1. Open the tailgate. Insert a flat-tip screwdriver into the specified position of the right tailgate trim, and remove the pin as shown.
2. Remove the clip and the right tailgate trim.
3. Remove the left tailgate trim in [...]

[Read more →]

Follow the steps below to maintain your belt case air cleaner:
Step 1 ­ Remove the left rear side cover.
Step 2 ­ Remove the five screws and retainer clip that secures the air cleaner housing cover. Remove the screw attached to the bracket that secures the air cleaner.
Step 3 ­ Inspect the air cleaner for excessive [...]

[Read more →]

This bulletin updates TSB 01-40-005 to add additional DTC code information. An improperly functioning input speed sensor or output speed sensor may result in the following four conditions:
1 “Check Engine” light on ‘
2. Harsh P-R or P-D engagement shock W I.
3. Transaxle accelerates in 1st gear to approximately 5000 rpm, then shifts into 3rd gear [...]

[Read more →]

What you will need for assembly:
1- socket wrench
1- 9/16 socket
1- Metric 13 socket (Prius uses metric bolts however a 9/16 works)
1- 9/16 flat wrench
1- protective eyewear
Step 1- Remove the 2 Black extendmyseat brackets from the packaging and locate the 4 black 3/8” provided bolts.
Step 2- Go to your vehicle with a socket wrench and a [...]

[Read more →]

The following information describes the installation procedure for the M-11572-GT “ENGINE START” push-button
into a 2005-‘09 Mustang.
STEP 1: Start by removing the (2) screws found at the rear of the center console underneath the armrest.
STEP 2: Remove the trim plate which surrounds the Shifter Handle (Auto) or Shifter Boot (Manual).
Note: Manual transmission applications will require removing [...]

[Read more →]