Automotive Manual, Car Parts and News

RSS Feed

Free PDF Download, Car Parts and Automotive News

99-04 Chevrolet Impala/Pontiac Grand Prix 3.8L #200-584 Installation

January 3rd, 2011 · No Comments

1. DISCONNECT NEGATIVE (-) BATTERY CABLE.
2. Remove throttle body air intake system.
3. Remove (3) nuts & studs from the throttle body & manifold. (Ref. “C”)
4. Remove support bracket from engine block to throttle body. (Ref. “D”)

[Read more →]


How to check the fuel pressure on Chevrolet s10?

January 1st, 2011 · No Comments

I have a 99 chevy s 10 with a 4.3 liter v6, it has a throttle body. I need to figure out how to check the fuel pressure and make sure the fuel pump is what is bad.

[Read more →]


How to fix the gas pedal on my 1994 Chevrolet Silverado 1500

December 31st, 2010 · No Comments

I have a 1994 Silverado z71 with a 5.7 v8 and when I first start to accelerate the gas pedal is really stiff and hard to push and what happens is it gets past the stiff part and I end up launching the car as if in the start of a race. This stiffness is [...]

[Read more →]


Why won’t my 88 Cadillac Deville idle when it’s cold?

December 28th, 2010 · No Comments

We got it last year, and it ran beautifully (still does, when it’s warm). At the beginning of the cold snap this winter, when I started it in the morning, it would sputter a little but would catch and run smoothly. Over the winter, the morning starts have been more and more “sputtery” for longer [...]

[Read more →]


01 Cadillac Deville, Vaccume leak?

December 27th, 2010 · No Comments

I have a 01 Cadillac Deville with a vaccume leak somewhere causing it to Idle funny only when its in open loop. Is there any common places these have vaccume leaks? How do I trace the leak when I can’t find it. Carb cleaner did not work.

[Read more →]


Nissan S14/S15 Intake Manifold Instruction Manual

December 23rd, 2010 · No Comments

It is important that a model specific service manual be used so the removal and installation of parts can be performed to factory specifications.
OEM Intake Manifold Removal
(1) Disconnect the negative terminal from the battery and drain the engine coolant.
(2) Remove the Intake piping from the throttle body.

[Read more →]


09 Nissan Cube Stillen Hi-Flow Intake

December 22nd, 2010 · No Comments

Installation: 1. Ensure that you have the correct kit prior to installation.
2. Remove the engine cover by removing the 2 bolts. Set aside as it will be reinstalled.
3. Disconnect the connector from the M.A.S. and unclip the wire harness from the air box. You will also need to remove the upper portion of the baffle [...]

[Read more →]


Nissan 300ZX Atmo Blow-Off Valve Adaptor Instructions

December 19th, 2010 · No Comments

FITTING YOUR BOV 300ZX ADAPTOR
Note: Please thoroughly read and understand both these instructions and the fitting instructions supplied with your BOV before commencing this installation.
Step 1. Locate the two boost hoses.
Step 2. Loosen the factory hose clamps securing the boost hoses to the intercooler pipe and throttle body.

[Read more →]


2006 Dodge Dakota/Mitsubishi Raider Air Charger P/N. 63-1546

December 11th, 2010 · No Comments

TO START:
1. Turn the ignition OFF and disconnect the vehicle’s negative battery cable.
2. Loosen the hose clamp at the throttle body and the air box mounting nut and then disconnect the crank case vent hose from the inline fitting.
3. Disconnect the stock intake tube from the intake plenum and lift to remove the air box [...]

[Read more →]


Bomz Racing 00-05 Dodge Neon SOHC Cold Air Intake Installation Guide

December 6th, 2010 · No Comments

Removal of Factory Intake
Turn the ignition OFF and disconnect the vehicle’s negative battery cable. Remove the wire loom from retaining clips. Loosen and remove the five airbox retaining bolts then remove airbox lid. Remove the stock air filter. Pull up and remove the fresh air intake from fender well. Remove the four throttle body retaining [...]

[Read more →]




?>